Roosevelt Water Association           

How to Detect Leaks

Here are some tips on simple things you can do or check at home to help conserve water.

Use your water meter to check for leaks
The best way too determine if you have a leak in your plumbing system, is by first checking your water meter. If you do not know where your meter is located you can call (360) 568-3450 or email Manager@RooseveltWater.com to get your meter location.
  

  • Make sure no water is being used inside or outside of your house.
    •   
  • Locate your water meter and check the leak indicator to see if it is moving. Depending on the brand of your meter, the leak indicator could be a small triangular shaped dial or a small silver wheel that rotates when water is flowing through the meter. If the dial is moving, chances are, you have a leak.
    •   
  • Or, you can also take a meter reading and wait 1 or 2 hours and take another meter reading (make sure no water is used during this time). If the reading has changed, you have a leak.

    • After you have determined that you have a leak, the next step is to determine if the leak is inside or outside of your house.

    1. Locate your home main shut off valve and shut off the water at the valve. Typically, you will find the shut off valve in the basement or garage directly behind an outdoor faucet, or outside below an outdoor faucet.
    2. Again, check the leak indicator for movement or use the meter reading method, making sure not to use any water during this period. If the leak indicator stops moving or there is no change in the meter readings, then you have a leak inside of the house. If the leak indicator continues to move or there is a change in the meter readings, then the leak is outside between the meter and the house.
    3. If you are unable to locate the leak, you may need to call a plumber.

    Leaking Faucets
    Leaking faucets are generally a result of a worn rubber washer. The washer on a sink is usually located under the handle. These are relatively easy to replace, if you have the right tools. It does require shutting off the water under the sink or at the main shutoff valve and removing the handle. (Note: faucet handles are not shutoff valves.) Check your local home center or hardware store on how to repair faucet leaks.

    Leaking Toilets
    Toilet leaks can waste hundreds of gallons and often times are silent. Even a small leak can add up to a lot of wasted water and money over time. Fortunately, most toilet leaks are easy and inexpensive to repair.

    To help determine if you have a leaking toilet, simply remove the tank lid and place a few drops of food coloring in back of the toilet tank. (If you don'?t have food coloring, you can purchase dye tabs from any hardware or home center). Wait about 30 minutes, without flushing, and then look in the toilet bowl to see of any color has come through. If the water is clear, water is not leaking. If you see food coloring in the bowl, you have a leak.

    In most cases, you will simply just need to replace the toilet flapper and/or filling mechanism. These are available at hardware or home center stores for about $8.00 each.

    Flapper Valve Leaks
    The most common reason for a leaking toilet is one that has an improperly working or sealing flapper. The flapper is the rubber valve in the bottom of the tank that lifts up when the toilet is flushed. If the flapper is worn or cracked, it allows water to continuously flow from the tank into the toilet bowl without flushing.

    Flush Handle Problems
    If the handle needs to be jiggled to keep the toilet from running¯, the flush level bar and chain (or the handle itself) may be sticking. Adjust the nut that secures it in the toilet tank. If that does not work, the handle may have to be replaced.

    Overflow Tube Leaks
    Ideally the water level should be set so that i?s about even with the fill line on the back of the toilet tank (approximately ½"¯ below the overflow tube). If the water is too high in the toilet tank and is spilling into the overflow tube, the water level can be adjusted by turning the adjustment screw or by very gently bending the float arm down so that the water shuts off at a level below the overflow tube.
    Note: If none of these steps solve the problem, you may need to contact a plumber to repair or replace the toilet.

    Underground Leak Detection
        Visual
    Look (and feel) for portions of your property that are always wet.

  • Look at your driveway, curb or street for evidence of water flow. The evidence may not be a steady stream of water; it may only be a puddle that never dries up, or a darker spot (as in what happens when water is spilt on dry concrete).

        Meter Reading
    Look at your water meter and write down the meter reading. Don't run any water for a few hours. Re-read your meter.

  • If it shows use, and you've already fixed all other known leaks, then you may have an underground leak.

    • Back to Conservation Tips Page